Can A Kindle Hdx7 Be Repaired

Introduction

Replacement guide for the display assembly on a Kindle Fire HDX 7" tablet.

The display associates is glued to the mid-frame and volition require some heat to brand removal possible.

• Insert an opening pick underneath the speaker bezel, and slide information technology along the perimeter to split up it from the tablet.

• The adhesive is strong and may require an iOpener, or rut gun, to soften.



• Remove the speaker bezel.

• Remove the six pink 3mm T3 Torx screws from the back case.

• Wedge opening picks around the perimeter between the display and back case.

• Work the opening picks around the perimeter until the two halves disengage from each other.

• Don't completely separate as the display ribbon cable still connects the two.

• Utilise the flat end of a spudger to pry upward and disconnect the rear panel press-fit connector from the motherboard.

• There may be a glue strip between the bombardment and the outside example. Gently pry the case open and utilize the apartment end of a spudger to separate the glue strip.

• Pry up the battery connector with the flat end of a spudger.

• iFixit adhesive remover contains acetone, a mild skin and centre irritant.

• Wear eye protection when handling and applying the adhesive remover. (Heart protection is included in your kit.)

• Practise not wear contact lenses without centre protection.

• Protective gloves are also included in your kit. If you are concerned about possible skin irritation, put your gloves on at present.

• Apply a small amount of adhesive remover (approximately 1 ml) evenly along the elevated edge of the battery cell.

• Expect ii-3 minutes for the liquid adhesive remover to penetrate underneath the bombardment prison cell before you go on to the next step.

• Slide a few opening picks betwixt the battery and the raised metal edge.

• Pry upwards to lift the battery up.

• Pace 15 may need to be repeated a few times to weaken the glue.

• Apply a modest amount of adhesive remover (approximately ane ml) underneath the battery and wait 2-3 minutes for information technology to penetrate.

• You may need to repeat this a few times.

• Keep prying up the battery.

• Remove the battery from the mid-frame.

• Grab the yellow record with a pair of tweezers and pull upwards to disconnect the press-fit connector.

• Use the apartment terminate of a spudger to disconnect the front camera press-fit connector from the motherboard.

• Remove the nine 3mm T6 Torx screws from the motherboard.

• Use a spudger to pry up and disconnect the antenna cable from the motherboard.

• Pull the antenna cable upwardly and off of the motherboard.

• Don't remove completely as it's soldered to the frame.

• Utilise a spudger to disconnect the second antenna cable from the motherboard.

• Use the apartment end of a spudger to pry upward and disconnect the front end photographic camera press-fit connector from the motherboard.

• Remove the front camera.

• Remove the motherboard from the tablet.

• Heating the edges of the tablet will aid soften the adhesive securing the display, making it easier to open.

• Use a hairdryer or prepare an iOpener and utilise it to the edge of the tablet for about 90 seconds in order to soften up the adhesive underneath.

• Insert an opening pick between the glass display and the metal mid-frame.

• Insert a second opening pick in a higher place the first.

• Roll the 2nd opening pick all the way around the perimeter of the display.

• Elevator upward on the glass display to remove information technology from the metal mid-frame.

Decision

To reassemble your device, follow these instructions in contrary society.

Embed this guide

Choose a size and re-create the code below to embed this guide as a small widget on your site / forum.

Preview

Can A Kindle Hdx7 Be Repaired,

Source: https://www.ifixit.com/Guide/Kindle+Fire+HDX+7-Inch+Display+Assembly+Replacement/112821

Posted by: piercevaggrosen.blogspot.com

Share this post